{"id":747,"date":"2026-09-02T01:20:34","date_gmt":"2026-09-02T01:20:34","guid":{"rendered":"https:\/\/sushichain.top\/product\/ice-cream-conveyor-chain\/"},"modified":"2026-09-02T05:17:18","modified_gmt":"2026-09-02T05:17:18","slug":"ice-cream-conveyor-chain","status":"publish","type":"product","link":"https:\/\/sushichain.top\/fr\/produit\/ice-cream-conveyor-chain\/","title":{"rendered":"Ice Cream Conveyor Chain"},"content":{"rendered":"
\n
\n
Product overview<\/div>\n

Ice Cream Conveyor Chain<\/h2>\n
\n
\n

The ice cream conveyor chain family uses dedicated attachments and abrasion-block interfaces rather than a single universal chain form. The series specification shows A, C, AB and CP arrangements with different pitches and interface dimensions. That variety matters because the product carrier, guide surface and indexing arrangement can change from one frozen-dessert machine to another. A replacement inquiry should begin with the exact existing configuration, not only the words 'ice cream chain'. Where the original chain number is unknown, clear top and side photographs plus pitch, roller diameter and attachment dimensions are the fastest way to narrow the configuration.<\/p>\n

For replacement work, treat the base chain, attachment or abrasion-block configuration and product carrier as one interface. The part should be compared with the conveyor that exists today, including any guide, carrier or sprocket modifications made after the original machine was commissioned.<\/p>\n<\/div>\n

\"Ice
Construction detail for replacement identification.<\/figcaption><\/figure>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
Mechanical interface<\/div>\n

Check the features that control fit and motion<\/h2>\n
\n
\"Ice
Additional configuration detail.<\/figcaption><\/figure>\n
\n

The key review points are carrier position, block clearance and product spacing. Measure several repeating features where possible instead of relying on one worn joint, rod or attachment. Photograph the component while it is still installed so running direction, guide contact and drive engagement are visible.<\/p>\n

Choose the configuration by matching the installed carrier geometry first, then the chain pitch and roller system. Confirm whether the line uses abrasion blocks, extended pins or a dedicated carrier around the joint. Record freezer or cooling-zone conditions, sanitation method, any icing exposure and whether the line indexes or runs continuously. For parallel-chain machines, measure the cross-machine center distance and check whether matched chain lengths are required. Do not mix dimensional rows from different A\/C\/AB\/CP configurations when preparing a replacement specification.<\/p>\n

When dimensions are uncertain, label them as measured from a worn sample rather than rounding them into an assumed nominal value. This makes it easier to distinguish a true dimensional conflict from normal service wear during technical review.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n
Dimensions<\/div>\n

Technical drawing and specification<\/h2>\n
\"Ice
Dimension drawing; use the table below for listed values.<\/figcaption><\/figure>\n

Dimension key:<\/strong> P = pitch; L = pin length; d = pin diameter; D = roller diameter; h = plate height; b1 = inner width; Lc = pin\/chain length where listed; T\/t = plate thickness notation; abrasion-block dimensions are shown exactly as listed.<\/p>\n

\n\n\n\n\n\n\n\n\n\n
Configuration<\/th>\nPitch P (mm)<\/th>\nPin Length L (mm)<\/th>\nPin Diameter d (mm)<\/th>\nRoller Diameter D (mm)<\/th>\nPlate Height h (mm)<\/th>\nWidth Between Inner Plates b1 (mm)<\/th>\nPin Length Lc (mm)<\/th>\nPlate Thickness T\/t (mm)<\/th>\nPlastic Abrasion Block Size (mm)<\/th>\nAdditional Plate Height (mm)<\/th>\n<\/tr>\n<\/thead>\n
C-SSIC150<\/td>\n150.00<\/td>\n57.00<\/td>\n11.85<\/td>\n30.00<\/td>\n26.00<\/td>\n16.00<\/td>\n59.50<\/td>\n4\/3<\/td>\n104\u00d720\u00d78<\/td>\n\u2014<\/td>\n<\/tr>\n
A-SSIC125<\/td>\n125.00<\/td>\n55.50<\/td>\n12.00<\/td>\n30.00<\/td>\n28.00<\/td>\n15.00<\/td>\n58.00<\/td>\n4\/3<\/td>\n75\u00d722\u00d77<\/td>\n18<\/td>\n<\/tr>\n
AB-SSIC50.8<\/td>\n50.80<\/td>\n26.50<\/td>\n11.55<\/td>\n30.00<\/td>\n25.80<\/td>\n10.00<\/td>\n57.80<\/td>\n3\/3<\/td>\n23\u00d723\u00d75<\/td>\n13.50<\/td>\n<\/tr>\n
CP-SSIC76.2<\/td>\n76.20<\/td>\n38.50<\/td>\n11.75<\/td>\n32.00<\/td>\n28.00<\/td>\n15.00<\/td>\n\u2014<\/td>\n3.00<\/td>\n68\u00d765<\/td>\n11.50<\/td>\n<\/tr>\n
CP-SSIC101.6<\/td>\n101.60<\/td>\n38.50<\/td>\n11.75<\/td>\n32.00<\/td>\n28.00<\/td>\n15.00<\/td>\n\u2014<\/td>\n3.00<\/td>\n68\u00d765<\/td>\n11.50<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

The table reproduces the available model\/configuration data for this product page. Values not listed here should be confirmed from the project drawing, current component or machine interface rather than inferred from another series.<\/p>\n<\/div>\n<\/section>\n

\n
\n
\n
\"Ice
Conveyor application for machine-interface review.<\/figcaption><\/figure>\n
\n
Application review<\/div>\n

Evaluate the component inside the complete conveyor path<\/h2>\n

Ice Cream Conveyor Chain is considered for ice-cream and frozen-dessert processing equipment. In addition to the component dimensions, state the product being conveyed, spacing, line speed, starts and stops, curve or incline conditions, process zones and sanitation method. These operating inputs help identify the interfaces that deserve extra attention during approval.<\/p>\n

Inspect the drive, supports, transfer points and return path for wear or modification. If damage repeats at one machine position, correct that interface before judging a new chain or belt. A replacement component cannot compensate for a burr, misaligned guide, damaged sprocket or unsupported transfer.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n
Installation<\/div>\n

Commission at low speed before normal production<\/h2>\n

Before connecting the loop, verify that every attachment clears guides and fixed machine parts through a complete hand rotation. Check carrier height and the relationship between the abrasion block and its wear surface. If the chain is used in an indexing machine, test the stop position at low speed before introducing product. A small pitch or attachment mismatch can appear acceptable on a straight run yet create a repeating positioning error at the drive sprocket or transfer point.<\/p>\n

After the initial empty run, compare the same observation points under representative load. Record any change in lateral position, articulation, transfer impact, noise or take-up position. A short, repeatable commissioning record makes it easier to separate normal bedding-in from a machine-interface problem that requires correction before routine production.<\/p>\n

\n
01<\/b>Inspect<\/strong><\/p>\n

Clean and inspect sprockets, guides, supports and transfers before installing the new component.<\/p>\n<\/article>\n

02<\/b>Align<\/strong><\/p>\n

Confirm running direction, lateral position and engagement without forcing the component into the track.<\/p>\n<\/article>\n

03<\/b>Run empty<\/strong><\/p>\n

Follow a marked joint or belt row through the complete loop at the lowest practical speed.<\/p>\n<\/article>\n

04<\/b>Add product<\/strong><\/p>\n

Introduce representative loading and recheck transfer, curve, tracking and return-path behavior.<\/p>\n<\/article>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n
Cleaning & inspection<\/div>\n

Keep the carrying surface and articulation points observable<\/h2>\n

Frozen dessert lines can combine moisture, sugar residue and cold surfaces. Cleaning plans should preserve attachment alignment and avoid residue accumulation around rollers, pins and abrasion blocks. After sanitation, inspect the blocks for uneven wear and make sure fasteners or attachment interfaces have not loosened. If product buildup changes friction at a sliding block, the drive load and positional repeatability can change even though the chain itself is not visibly damaged.<\/p>\n

Record any recurring edge wear, polished guide contact, deformed attachment, pin movement, hook misalignment or mesh distortion. A dated photograph at the same inspection points makes trend changes easier to recognize than an isolated end-of-life inspection.<\/p>\n<\/div>\n<\/section>\n

\n
\n
Replacement approval<\/div>\n

Freeze the dimensions and checks that matter for repeat orders<\/h2>\n

After the first acceptable sample or production batch is confirmed, retain the model\/designation, current dimension record, approved photographs and the machine position where the component is used. For Ice Cream Conveyor Chain, include the features that control carrier position, block clearance and product spacing. If the conveyor is modified later, update the interface record instead of assuming the historical part number still describes the machine.<\/p>\n

For a new enquiry, keep each model as a separate technical line even if several models are combined commercially. State sample quantity and production quantity separately. If a particular material, surface condition or special process is mandatory, identify it as a requirement so it can be reviewed against process minimums.<\/p>\n<\/div>\n<\/section>\n

\n
\n
Engineering checklist<\/div>\n

Questions to close before production approval<\/h2>\n
\n
Mating geometry<\/strong><\/p>\n

Confirm base chain, attachment or abrasion-block configuration and product carrier against the current machine. Record where the part is supported, guided and driven, and identify any feature that has been repaired or modified.<\/p>\n<\/article>\n

Product handling<\/strong><\/p>\n

Describe product footprint, spacing, orientation and transfer points for ice-cream and frozen-dessert processing equipment. Note curves, inclines or hanging sections that change the clearance requirement.<\/p>\n<\/article>\n

Service observations<\/strong><\/p>\n

Photograph recurring wear and identify the machine position where it occurs. Check carrier position, block clearance and product spacing before deciding that the old component itself caused the problem.<\/p>\n<\/article>\n<\/div>\n

For incoming inspection, select dimensions that can be measured consistently and tie them to the drawing or approved sample. Do not use appearance alone as the acceptance criterion when two configurations share a similar overall form. For commissioning, document the low-speed result before normal production so later maintenance has a baseline for comparison.<\/p>\n

When ordering repeat quantities, state whether the machine, product format or cleaning process has changed since the previous batch. A small change to guides, transfers or product spacing can alter which interface controls performance even when the nominal component model remains the same.<\/p>\n<\/div>\n<\/section>\n

\n
\n
Project verification<\/div>\n

Confirm Ice Cream Conveyor Chain against the current conveyor before production quantity<\/h2>\n

A dimensional table identifies the listed product, but replacement approval should also compare the carrier or abrasion-block arrangement, base chain and guide system with the machine that will receive the part. For Ice Cream Conveyor Chain, record carrier orientation, repeating spacing, block clearance and drive engagement using the same datums that will be used for incoming inspection. If an old component is worn, measure several repeats and photograph the least-damaged reference area rather than selecting one convenient value.<\/p>\n

Photographs should show more than the loose component. Include the drive and return path, both conveyor edges, the tightest transition, and any location where wear repeats. Add one overall machine view so the running direction and product path are unambiguous. When a guide, sprocket, support or transfer has been repaired, note that change because the current as-built interface is the one the replacement must fit.<\/p>\n

For sample approval, agree on the critical dimensions and visible configuration before the sample is produced. During low-speed testing, follow one marked joint, carrier or belt row through a complete revolution and note any rubbing, lift, skew, cyclic noise or product-position change. If the symptom appears at one fixed machine location, inspect the surrounding hardware before changing the component specification.<\/p>\n

For repeat orders, retain the accepted model, dimension record and machine position together. This reduces ambiguity when the same facility uses similar components on several lines. If the product format, line layout or cleaning process changes, include that change in the next enquiry even when the component designation is unchanged.<\/p>\n<\/div>\n<\/section>\n

\n
\n
Frequently asked questions<\/div>\n

Ice Cream Conveyor Chain FAQ<\/h2>\n
\n
\nWhich ice cream chain configuration should I quote?<\/summary>\n

Use the existing chain number when available. Otherwise send the A\/C\/AB\/CP-style geometry, pitch, roller diameter, attachment measurements and machine photographs.<\/p>\n<\/details>\n

\nAre all listed configurations the same pitch?<\/summary>\n

No. The specification table includes pitches from 50.80 mm to 150.00 mm, so pitch must be measured rather than assumed.<\/p>\n<\/details>\n

\nWhy are abrasion-block dimensions important?<\/summary>\n

They define the sliding or carrier interface. A block with the wrong footprint can change guide contact, height and positioning.<\/p>\n<\/details>\n

\nShould I provide operating temperature?<\/summary>\n

Yes. Temperature and icing conditions help review material and clearance suitability even though the series specification table does not publish a universal operating-temperature rating.<\/p>\n<\/details>\n

\nCan different models be combined in one RFQ?<\/summary>\n

Yes. List each configuration and quantity separately so the quotation can keep model-specific geometry clear.<\/p>\n<\/details>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n
\n
Inspection & machine review<\/span><\/p>\n

Check measurable features before production release<\/h2>\n<\/div>\n

Use reproducible dimensions and current machine photographs for incoming inspection and replacement approval.<\/p>\n<\/div>\n

\n
\"Ice
Dimensional and interface inspection.<\/figcaption><\/figure>\n
\"Ice
Production-line handling and visual inspection.<\/figcaption><\/figure>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
Related selection guidance<\/div>\n

Compare the component within the correct conveyor family<\/h2>\n

For adjacent configurations and replacement context, review the food conveyor chain family<\/a>. If the existing machine has been modified, use the engineering selection guide<\/a> to record the drive, guide, transfer and operating conditions before approving production quantity.<\/p>\n

Compare the complete dimension set and the current machine interface before treating a nearby model as interchangeable. In replacement work, photograph the drive and return path as well as the visible carrying section; this helps identify whether guide, sprocket, support or transfer changes are part of the project.<\/p>\n<\/div>\n<\/section>\n

\n
\n
RFQ<\/span>Send the model, dimensions, machine photos and quantity.<\/strong><\/p>\n

Include the current conveyor path and operating conditions when the project is a replacement or retrofit.<\/p>\n<\/div>\n

Demander un devis<\/a><\/div>\n<\/section>","protected":false},"excerpt":{"rendered":"

Ice cream conveyor chain family with A, C, AB and CP configurations and dimensional options for product carriers and abrasion-block interfaces.<\/p>","protected":false},"featured_media":716,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_brand":[],"product_cat":[1423],"product_tag":[],"class_list":["post-747","product","type-product","status-publish","has-post-thumbnail","product_cat-food-conveyor-chains","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/product\/747","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/comments?post=747"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/media\/716"}],"wp:attachment":[{"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/media?parent=747"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/product_brand?post=747"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/product_cat?post=747"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/sushichain.top\/fr\/wp-json\/wp\/v2\/product_tag?post=747"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}