Rod Reinforced Conveyor Belt
Rod reinforced belts combine spiral wire elements with transverse rods to create a wire conveying surface that can be specified by spiral pitch, rod pitch, rod thickness and rod diameter. The series specification distinguishes RR and RRW designation styles and publishes representative nominal weights. These values are useful for matching an existing belt, but they should be combined with actual belt width, edge construction, drive arrangement and application duty before a replacement is released. Because the product is open mesh, airflow, drainage and product support also depend on the selected pitch combination.
更换部件时，应将皮带网、横杆、边缘、支撑件和驱动装置视为一个整体。更换的部件应与现有输送机进行比较，包括原机器投入使用后对导轨、托架或链轮进行的任何改动。
检查控制合身度和运动性能的功能。
关键的评估要点包括产品支持、跟踪、转移和驱动啮合。尽可能测量多个重复出现的特征，而不是仅仅依赖于一个磨损的接头、杆或附件。在部件仍安装到位的情况下拍摄照片，以便清晰地显示运行方向、导向接触和驱动啮合情况。
Start with the four designation parameters, then define overall belt width, useful carrying width, edge style and any side or product guides. For food processing, also describe the product footprint: a belt that supports a tray or large baked item may not support small loose pieces with the same spacing. If the belt passes through heating, cooling, washing or drying equipment, state the temperature cycle and cleaning chemistry. The specification table provides nominal weight, not load capacity; required conveying load and support spacing must therefore be evaluated separately.
当尺寸不确定时，应标注为根据磨损样品测量所得的尺寸，而不是将其四舍五入为假定的标称值。这样有助于在技术审查过程中区分真正的尺寸偏差和正常的使用磨损。
技术图纸和规范
尺寸图例： RR/RRW designation: 1 = spiral pitch; 2 = rod pitch; 3 = rod thickness; 4 = rod diameter. The table lists nominal weight per square metre for representative configurations.
| 指定 | 重量（千克/平方米） |
|---|---|
| RR-27-25-4.0-4.0 | 13.5 |
| RR-25-23-4.0-3.2 | 17.1 |
| RR-20-18-3.2-3.2 | 13.9 |
| RR-16-13-3.2-3.2 | 19.5 |
| RR-13-10-2.6-2.6 | 16.3 |
| RR-12-12-2.0-2.0 | 8.7 |
| RR-10-10-2.0-2.0 | 10.8 |
| RR-12-12-1.6-1.6 | 5.3 |
| RR-8-6-1.6-1.6 | 10.3 |
| RRW-12.5-25-5.0-4.0 | 31.7 |
| RRW-4-12-2.6-2.6 | 39.1 |
此表格列出了该产品页面可用的型号/配置数据。未在此列出的数值应根据项目图纸、当前组件或机器接口进行确认，而不能从其他系列推断。
评估整个传送路径内的组件
Rod Reinforced Conveyor Belt is considered for food-processing, cooling, washing and transfer equipment. In addition to the component dimensions, state the product being conveyed, spacing, line speed, starts and stops, curve or incline conditions, process zones and sanitation method. These operating inputs help identify the interfaces that deserve extra attention during approval.
检查驱动装置、支撑件、传动点和回程路径是否存在磨损或改动。如果损坏在机器的同一位置反复出现，则在决定是否更换新的链条或皮带之前，应先修复该接口。更换部件无法弥补毛刺、导轨错位、链轮损坏或传动装置缺乏支撑等问题。
在正常生产前以低速进行调试
During installation, align support rails so the reinforced rods are not forced into a skewed path. Check the drive interface across the full belt width and verify that the belt tracks without rubbing a frame edge. Run empty first, then with representative product distribution. An open wire belt can look straight at the center while one edge is accumulating pitch error, so inspect both edges and the cross-rods during commissioning.
首次空载运行后，在典型负载下对相同的观察点进行比较。记录横向位置、铰接、传递冲击、噪音或收紧位置的任何变化。一份简短且可重复的调试记录有助于区分正常的磨合过程和需要在正式生产前进行纠正的机器接口问题。
安装新部件之前，请清洁并检查链轮、导轨、支架和传动装置。
在不强行将部件压入轨道的情况下，确认运行方向、横向位置和啮合情况。
以尽可能低的速度，沿着标记好的关节或皮带行完成整个环。
引入代表性载荷并重新检查传递、曲线、跟踪和返回路径行为。
保持承载面和关节点清晰可见
Keep product residue from packing around rod intersections and edge loops. Cleaning should preserve wire shape and avoid tools that nick or bend the mesh. Inspect for localized wire polishing, cracked welds where present, uneven cross-rod movement and edge distortion. If a belt has been repeatedly shortened after damage, measure its current width and pitch again rather than relying on the original purchase record.
记录任何反复出现的边缘磨损、抛光导向接触、连接件变形、销钉移动、钩子错位或网格扭曲等情况。在相同的检查点拍摄带有日期的照片，比单独的报废检查更容易识别趋势变化。
冻结对重复订单至关重要的尺寸和检查项目
After the first acceptable sample or production batch is confirmed, retain the model/designation, current dimension record, approved photographs and the machine position where the component is used. For Rod Reinforced Conveyor Belt, include the features that control product support, tracking, transfers and drive engagement. If the conveyor is modified later, update the interface record instead of assuming the historical part number still describes the machine.
对于新的询价，即使多个型号在商业上组合使用，也应将每个型号作为单独的技术线列出。样品数量和生产数量应分别说明。如果特定材料、表面状态或特殊工艺是强制性的，请将其明确列为要求，以便与工艺最低标准进行比对。
生产批准前需要解决的问题
确认皮带网、横杆、边缘、支撑件和驱动装置与当前机器的匹配情况。记录零件的支撑、导向和驱动位置，并标明任何已维修或改装的部件。
描述食品加工、冷却、清洗和输送设备的占地面积、间距、方向和输送点。注意可能改变净空要求的曲线、倾斜或悬挂部分。
拍摄反复出现的磨损照片，并确定磨损发生的机器位置。在确定是旧部件本身导致问题之前，请检查产品支持、跟踪、转移和驱动因素。
对于来料检验，应选择可稳定测量的尺寸，并将其与图纸或已批准的样品进行比对。当两种配置具有相似的整体形状时，不要仅以外观作为验收标准。对于调试，应在正常生产之前记录低速运行结果，以便后续维护工作有基准进行比较。
订购重复批次产品时，请说明机器、产品规格或清洗流程是否与上一批产品有所不同。即使组件的标称型号保持不变，导轨、传送装置或产品间距的细微变化也可能导致控制性能的接口发生改变。
Confirm Rod Reinforced Conveyor Belt against the current conveyor before production quantity
A dimensional table identifies the listed product, but replacement approval should also compare the wire mesh, rods, edges, supports and drive with the machine that will receive the part. For Rod Reinforced Conveyor Belt, record belt width, repeating geometry, edge guidance and transfer support using the same datums that will be used for incoming inspection. If an old component is worn, measure several repeats and photograph the least-damaged reference area rather than selecting one convenient value.
照片应清晰展现除松动部件以外的更多信息，包括驱动和回程路径、输送机的两侧边缘、最急的过渡区域以及任何重复磨损的位置。此外，还应添加一张整机视图，以便清晰地显示运行方向和产品路径。如果导轨、链轮、支撑件或传送装置已维修，请务必记录这一变更，因为更换部件必须与现有安装接口相匹配。
样品审批前，应在样品生产前确认关键尺寸和可见结构。低速测试时，沿标记的连接点、托架或皮带排旋转一周，并记录任何摩擦、抬升、倾斜、周期性噪音或产品位置变化。如果故障现象出现在机器的某个固定位置，请在更改组件规格前检查周围的硬件。
对于重复订单，请保留已确认的型号、尺寸记录和机器位置信息。这样可以减少同一工厂在多条生产线上使用类似组件时可能出现的歧义。如果产品规格、生产线布局或清洗流程发生变化，即使组件名称不变，也应在下次询价时注明这些变化。
Rod Reinforced Conveyor Belt FAQ
What do the RR/RRW numbers mean?
The series specification identifies the four designation positions as spiral pitch, rod pitch, rod thickness and rod diameter.
Does the series specification weight equal load capacity?
No. It is nominal belt weight per square metre. Conveying load depends on the complete belt, supports, drive and application.
What dimensions are needed for a replacement?
Provide designation, belt width, edge style, drive interface, overall length or loop length and photographs of the installed belt.
Can the belt be used for food cooling?
Open wire construction is commonly selected where airflow or drainage is needed, but suitability must be checked against product support, temperature and sanitation requirements.
What should be checked at the edges?
Look for rubbing, stretched loops, bent rods and unequal tracking because edge damage often develops before failure is obvious in the center.
在产品发布前检查可衡量的功能。
使用可重复测量的尺寸和当前机器照片进行来料检验和更换批准。
如果项目是更换或改造，则需包含当前的输送机路径和运行条件。
